Customer Feedback
Read what customers say about our products. Thanks to everyone for sending us your pictures and feedback.
Do you have a question or comment for us? Please see our Requests and Comments page or email yourcovers@pmli.com.
Comments About PML Differential Covers
- "Hi Guys, I have purchased a rear cover for my 2002 Chevy dually. It was a VERY NICE cover. Nice hardware also, looks GREAT on the truck, many questions where I got it. I will spread the word of your quality products. I will be buying the Allision trans pan from you next. I do have one question. I have a 2000 S10 blazer that has the ZR2 option. I was told that this is a 8 1/2" gear rather than the 7 1/2" gear. Do you know about this? I would like to put a rear cover on it also. Thanks for any help and keep up the great work. Craig C. Collier"
 This picture and quote come from Marshall in MA, who owns an '03, Ram 3500 4X4.
"I got my PML differential cover in the mail the other day and decided to install it this morning. The cover is a sand cast aluminum piece that adds an additional quart of capacity to the rear end, it also has a magnetic drain plug. I have wanted to try one of these covers because it is reasonably priced, adds capacity, allows easy draining in the future, and seals using all the factory bolts and the factory gasket, it might add additional cooling with the fins but that may be negligable. The install was easy just bolt on."
Click here for a larger picture of the PML AAM 11.5 RG, 14 Bolt P/N 9511 installed on Marshall's truck. He wrote this on the www.turbodieselregistry.com, 3rd generation Ram forum and sent us additional pictures.
Comments About PML Transmssion Pans
- David Morrison installed a PML Dodge transmission pan (P/N 9393) with temperature sensor. He was kind enough to take pictures and document the process. He sent us a PDF file with pictures and information. The document shows that the new 48re tranny is same pan as 47re tranny. Click here to read the PDF file.
- From a customer who purchased the PML Dodge Transmission Pan (P/N 9393):
"Comments: Awesum pan. Painted mine and left it sitting in front of my 1998 Dodge Diesel - a lot of front end weight. Forgot about it while it was drying and got into the truck to drive off. Cliped the side of the pan and slid it under the truck. Any other stock pan would have been toast. No damage whatsoever. Thanks for the good product. John Hansen"
- From a customer who purchased our Ford 4R70W Deep Transmission Pan:
"Hi, recvd my 6985 pan the other day, installed it Saturday. Fit great and look fantastic! ! Thanks for a great product, and getting it out so quickly.........! ! ! Jim"
- From Les Martin, who purchased the PML Ford 4R55E, 4R44E, A4LD, 5R55E Deep Transmission Pan:
David,
Below is a digital photo of the factory A4LD transmission pan on my 1992 Aerostar...................
(click here for photo)
Below is a picture of PML's 3 Quart + Transmission Pan...............................
(click here for photo)
Please use these images any way you see fit to promote these excellently crafted pans.
With the use of your pan and AMSOIL Synthetic lubricants I was able to attain 72 Degrees F lower operaturing temperature
according to the transmission shop where I had the pan installed.
Sincerest appreciation,
Les Martin
President The Oil Zone, Salsbury, MD, 410-548-5823
Comments About PML Valve Covers
- Scott and Shari in Oklahoma wrote this about our Big Block Corvette® Valve Covers:
David
You were kind enough to sell me a set of your Corvette valve covers for
our big block 63 some months ago and I wished to update you on them.
I think I am going to have to take them off.
Because as you know lookers always check out the engine first and when
they do and see your valve covers they start going "Wow, where did you
get those?" and they quit looking at the rest of the Corvette. Its as
if I just took your covers and laid them on the ground as if they were
on an engine in a Corvette.
On our 50th Anniversary of the Corvette Caravan to Nashville a group of
Corvetters from Australia wanted some for a right hand drive Corvette.
Why would right hand drive matter?
Anyway, I am of course just kidding about taking them off. We feel that
they certainly enhance our Corvettes engine. I hope that a little
exposure in the Midwest has helped your sales.
Thanks Scott and Shari
Click here to see a picture of Scott and Shari's Corvette engine.
- Bill in Santa Rosa sent us pictures of our Small Block ChevyTM Valve Covers with fins and the Ford logo on his 1934 Ford Cabriolet:
 
- Mike Olsen put PML Small Block Chevy Valve Covers with Chevrolet® Script in orange powder coating on his El Camino. Click on images to view larger ones in separate window:
   
General Motors Trademarks are used under license to PML, Inc.
Links to Websites - Installations and Projects
- John and Nancy put a PML Dodge transmission pan and a Dana 60 differential cover on their 1968 Plymouth Barracuda Fastback. Click here to see the transmission pan and engine installation. Click on their "Rear End" link on the right side of their web page for the differential cover.
- See the installation of a Dodge differential cover on Hemi Truck Club website. Click here.
See also our page with shows, magazine articles and installations. Click here.
|
|
|
